您好,欢迎访问巨正东科技官方网站!

焊锡机_自动焊锡机_全自动焊锡机品牌领导者【首选巨正东焊锡机厂家】

致力于工业自动焊锡机器人的研发与生产

不仅仅是产品销售,更是技术服务

全国服务热线:

电话

联系我们
自动焊锡机咨询
深圳市巨正东科技有限公司

公司电话:0755-8322-7111

服务电话:13823729649

企业邮箱:zh@juzhengdong.com

地址:深圳市宝安区新桥街道中心路万丰98工业城19栋3楼

当前位置:首页 » 新闻资讯 » 常见问题解答 » 关于自动焊锡机的保养

关于自动焊锡机的保养

文章出处:焊锡机_自动焊锡机_全自动焊锡机品牌领导者【首选巨正东焊锡机厂家】人气:-发表时间:2018-10-29 00:00:00【
摘要 : 虽然使用自动焊锡机能节省人力成本,提高焊接效率,然而作为自动化设备来说平时一定要做好保养,才能延长机器的使用寿命。

  虽然使用自动焊锡机能节省人力成本,提高焊接效率,然而作为自动化设备来说平时一定要做好保养,才能延长机器的使用寿命。如果这个没有去做好,那么可能会导致设备出现各种问题。譬如自动焊锡机的烙铁头,就自动焊锡机而言使用完后需要做好烙铁头的保养,这点也是最常见的问题,保养得好可以延长自动焊锡机的使用寿命,如果不保养好那么在使用过程中可能会出现各种各样的问题,今天给大家分享一下自动焊锡机烙铁头的日常保养工作:


       Although the use of automatic soldering machine to save labor costs, improve welding efficiency, but as an automation equipment in peacetime must do a good job of maintenance, in order to extend the life of the machine. If this is not done well, it may lead to various problems in the equipment. For example, the automatic soldering machine iron head, the use of automatic soldering machine after the need to do a good maintenance of iron head, this is also the most common problem, good maintenance can extend the service life of automatic soldering machine, if not well maintained in the use of the process may be a variety of problems, today to share with you The daily maintenance work of soldering head of automatic soldering machine:


  大家都很明白烙铁头是自动焊锡机最重的结构组成部分,也是影响到自动焊锡机直接使用寿命的重要零件,烙铁头属于易损耗件,可以说是自动焊锡机部分当中最脆弱的部分,属于易消耗品的,烙铁头体积是虽然小,然而平时若没有做好保养,那么给你带来的麻烦也不小,为了在不影响的生产效率,做好烙铁头的日常保养是离不开的也是非常重要的一个环节,保养工作是不会占大家太多时间的,只要在接焊前后记得以下步骤就可以了:


       Everyone knows that the iron head is the heaviest structural component of the automatic soldering machine, and it is also an important part that affects the direct service life of the automatic soldering machine. If you do not do a good job of maintenance, then the trouble to you is not small, in order to not affect the production efficiency, do a good job of daily maintenance of iron head is inseparable from a very important link, maintenance work will not take up too much time, as long as before and after welding remember the following steps:


  1、选择正确、适当的温度,过高的温度会减弱烙铁头的功能、加快其氧化,相对缩短使用寿命。建议第一次加热时温度不要太高(260°左右),用锡覆在烙铁头上,以便去除包在上面的氧化物。在能够工作的情况下,尽量使用较低的温度,较低的温度也可以充分焊接,且可分保护对于温度敏感之元件。一般建议使用温度350~380度。1.5mm以下小焊点350~360度,2.5mm以上大焊点370~380度。


       1. Choosing the right and proper temperature, the excessive temperature will weaken the function of the iron head, accelerate its oxidation, and shorten its service life. It is recommended that the temperature should not be too high at the first heating (about 260 degrees). Tin is coated on the iron head to remove the oxide coated on it. In the case of working, try to use a lower temperature, lower temperature can also be fully welded, and can be separately protected for temperature sensitive components. It is generally recommended to use a temperature of 350~380 degrees. 1.5mm less solder joints 350~360 degrees, 2.5mm larger solder joints 370~380 degrees.


  2、自动焊锡机在焊接前用海棉擦拭烙铁头。如果烙铁头的镀锡部分含有黑色氧化物时,可镀上新锡层,再用湿润的清洁海绵抹净烙铁头。如此重复清洁,直到彻底除去氧化物为止,然后再涂上新锡层,并定期地对烙铁头进行清洁。


       2. Automatic solder machine wipes the iron head with sponge before welding. If the tin plating part of the iron head contains black oxide, a new tin layer can be plated, and then wipe the iron head with a wet clean sponge. This is repeated until the oxide is completely removed, then a new tin coating is applied, and the iron head is cleaned regularly.


  3、在不使用自动焊锡机时,应记得关闭电源,将烙铁头在清洁海绵上擦拭干净,然后上一层新的锡层,再次使用之前,还是将烙铁头在清洁海绵上擦拭干净,然后上一层新锡,不可加任何化合物于沾锡面。


       3. When not using the automatic soldering machine, remember to turn off the power supply, wipe the soldering iron head clean on the clean sponge, and then a new layer of tin, or wipe the iron head clean on the clean sponge before reusing, and then a new layer of tin, not adding any compounds on the tin surface.


  4、烙铁头第一次使用时,务必先将烙铁头温度调至220度,让烙铁头的上锡部位充分吃锡,最好是浸泡在锡堆里5分钟,然后在清洁海绵上擦拭干净,并把烙铁温度再次调至300度,重复上述程序,最后把烙铁温度调至所需使用温度进行使用。目的是在烙铁头上出锡层形成一层全面保护膜,防止其在高温状态下被氧化,导致热传输失效。


       4. When the iron head is first used, it is necessary to adjust the temperature of the iron head to 220 degrees, so that the tin on the iron head can be eaten sufficiently, preferably soaked in the tin pile for 5 minutes, then wiped clean on the clean sponge, and the iron temperature is again adjusted to 300 degrees, repeat the above procedure, and finally adjust the iron temperature to the required use temperature. For use. The purpose is to form a comprehensive protective film on the tin layer of the soldering iron head to prevent it from being oxidized at high temperature, resulting in the failure of heat transfer.


  通过以上四点相信大家在用自动焊锡机时一定要注意好,否则会影响到生产效率,一个企业如果生产效率受到影响,那么将会导致生产成本过高交期无法达标,这是企业最重要的问题。为了使自动焊锡机设备运行正常,那么保养工作是必不可少的。


        Through the above four points I believe we must pay attention to the use of automatic soldering machine, otherwise it will affect the production efficiency, an enterprise if the production efficiency is affected, then it will lead to the production cost is too high due date can not meet the standard, this is the most important problem for enterprises. In order to make the automatic soldering machine run normally, maintenance is essential.

相关阅读

此文关键字:关于自动焊锡机的保养
我要评论:  
*内 容:
验证码: 点击刷新换一张
 

共有-条评论

正在加载...